Béton
Strain gauges
ISO 6784 | ASTM C469 | BS 1881:121 | DIN 1048 | UNI 6556
Des images
DESCRIPTION GÉNÉRALE
DESCRIPTION GÉNÉRALE
They provide a very accurate electrical signal, strictly proportional to the strain of the specimen submitted to load application, for determining the Elastic Modulus and strength characteristics as alternative to the Compressometer-Extensometers 55-C0222/G. They can be applied to the specimen surface by a special Adhesive-Catalyst agent and other accessories all included in the 82-P0399/C Strain gauge application kit.
Up to 4 strain gauges ¼ bridge, and up to 8 ½ bridge, can be directly connected by one or two interfaces 82-P0398 to to our automatic control consoles Advantest, MCC or Automax Multitest which are suitable for cyclic loading and automatic determination of the Modulus of Elasticity.
Strain gauges can also be connected, by one or two interfaces 82-P0398, to a suitable data logger as, for example, our model 82-P9008 when the load application on the specimen is performed with Automatic compression testers as, for example the AUTOMAX and PILOT models. In this case, one of the channels of the Datalog 82-P9008 should be used for the load signal coming from an additional pressure transducer with selecting valve fitted to the compression tester.
Please get in touch with our technicians for complete information and service.
Up to 4 strain gauges ¼ bridge, and up to 8 ½ bridge, can be directly connected by one or two interfaces 82-P0398 to to our automatic control consoles Advantest, MCC or Automax Multitest which are suitable for cyclic loading and automatic determination of the Modulus of Elasticity.
Strain gauges can also be connected, by one or two interfaces 82-P0398, to a suitable data logger as, for example, our model 82-P9008 when the load application on the specimen is performed with Automatic compression testers as, for example the AUTOMAX and PILOT models. In this case, one of the channels of the Datalog 82-P9008 should be used for the load signal coming from an additional pressure transducer with selecting valve fitted to the compression tester.
Please get in touch with our technicians for complete information and service.
Technical specifications
Models 82- | P0390 | P0391 | P0392 | P0393 | P0396 |
Grid width mm0,9 | 0,9 | 1,2 | 2,3 | 1 | 1 |
Gauge length mm | 10 | 20 | 30 | 60 | 120 |
Resistance ohm | 120 | 120 | 120 | 120 | 120 |
Bridge | ¼ | ¼ | ¼ | ¼ | ¼ |
No. of gauges per package | 10 | 10 | 10 | 10 | 10 |
Ordering info
82-P0390Strain gauge, 10 mm gauge length. Pack of 10
82-P0391
Strain gauge, 20 mm gauge length. Pack of 10
82-P0392
Strain gauge, 30 mm gauge length. Pack of 10
82-P0393
Strain gauge, 60 mm gauge length. Pack of 10
82-P0396
Strain gauge, 120 mm gauge length. Pack of 10
82-P0399/1
Connecting terminals, 50 pairs sheet
82-P0399/C
Strain gauge application kit including: conditioner, neutralizer, acetone, tweezer, adhesive with catalyst agent, 100 m of bipolar cable, solder, soldering iron, scalpels, scissors, duct tape, sellotape, sandpaper and carrying case.
82-P0398
Compensation device for up to 4 Wheatsone bridges with ¼ or ½ bridge setup
Accessories
82-P0399/P22Adhesive and catalyst agent to glue the strain gauge to the specimen.
(Part of kit 82-P0399/B)
Documents







