Controls Group http://www.controls-group.com/images/logo_controls.gif Automax SMART line, fully automatic tester Automax SMART line, fully automatic tester
close
Hormigón

Automax SMART line, fully automatic tester

The automatic system controlled by digital unit and/or PC, featuring Energy Saving technology and two frame control, expandable to three

PRINCIPALES CARACTERÍSTICAS
  • PC control option
    When connected to PC, the system is fully computerized and controlled by the Data Manager software
  • Accurate load rate control for quality testing
    An accurate and constant load rate application without large fluctuations (typically 10% of the pre-set value) not only guarantees testing to Standards and reliability of results, but also allows the test to be performed by operators who do not have experience.
  • The advantage of the test automation.
    The test cycle with closed loop digital feedback is automatically performed by simply pressing the start button. The load-time graph and the actual load rate are displayed in real time during the test. Correct test execution according to the selected Standard, is continuously and automatically controlled.
  • Energy Saving test system
    “ES technology” features accurate oil flow control, conforming to Standards, resulting in no oil dispersion, silent operation, cold oil temperature and low energy consumption  (save over 30% compared to traditional systems).
  • High flexibility: can control testing frames from 100 to 5000 kN
    AUTOMAX  can fit all our compression and flexural testing frames performing accurate and reliable tests also for low strength results. It can also be used for other make compatible hydraulic compression and flexural frames
  • Third frame control option
    AUTOMAX can be upgraded, as option, with distributor block for the non simultaneous control of a third frame as, for example, Flexural testing frame and Cement compression frame. Active frame selection is made via the display/software.An ideal and economical solution to the automation of the most important tests on concrete and cement specimens.
  • Recording facility of up to 10 test profiles for each channel allowing quick and easy test start
DESCRIPCIÓN GENERAL
DESCRIPCIÓN GENERAL

This introduction has been designed to fit all our models of compression and flexural frames ranging from 100 to 5000 kN. Has been further upgraded using the latest technologies thus maintaining a very competitive price. The Automatic compression testers fitted with the Automax System have been the most reliable, and advanced solution for the Central Concrete Testing Laboratories, Private Laboratories and Contractors


Very Often, so be used as an old fashioned compression tester our Automax Smart-Line, thus granting high accuracy and reliability. This application requires a suitable pressure transducer and connecting cable. See \ # pressure-transducers \ #
 
Description
The Automax System is also offered as a part of the machine compression ( Automax, Super-Automatic EN testers for cubes, cylinders and blocks , Automax, Super-Automatic ASTM testers for cylinders ) but it is also available as a stand-alone control console . The two solutions are technically identical and can be selected according to customer requirements
.
Also, the front panel of the electronic control system is programmed to be loaded into a serial printer. See Upgrading options.
PC software 82-SW / DM (new release compatible only with SMART LINE units) for PC remote control , real time acquisition and management of test data. See accessories.
The use and the specimen shape and dimensions.
Más +

Especificaciones Técnicas

The AUTOMAX Control system features:

HYDRAULIC GROUP
  • Dual stage pump: centrifugal low pressure high delivery for fast approach and automatic switch to radial multi-piston high pressure for loading
  • DC motor, 720 W, 50-60 Hz
  • Max working pressure 650 bar
  • Third frame connection option (not simultaneous use only), Active frame selection by software.
  • Energy Saving technology to reduce the power consumption and silent operation
HARDWARE
  • 132000 points high resolution / stability analogical channels
  • Touch screen graphic display 240x128 pixels, icons driven showing figures and diagrams
  • Large storage capacity on USB pen drive of test data downloadable to PC
  • Ethernet port for communication with PC
  • Integrated graphic printer as optional
FIRMWARE
  • Simultaneous display of load, specific load, actual load rate and load / time graph
  • LAN connection to PC for transmission, in real time, during loading, of load and time values
  • Easy firmware update through Ethernet port
  • Memory management with display of stored tests, download of data to internal printer or PC, delete single test or reset entire memory
  • Automatic multi-coefficient calibration with automatic storage of data without manual editing
  • Multi-coefficient calibration procedure with automatic storage of data
  • Recording facility of 10 test procedures for each channel including: type of test (eg compression, flexural, indirect tensile), specimen size and shape, load rate, standard in use, and other general information. Each of the recorded test procedures can be activated by default to save time.
  • Compatible with the Data Manager 82-SW / DM software, new release tailored on the requirements of laboratories for construction materials, for real time data acquisition, display and management
  • 12 languages, Unit selection, etc.
  • Screen saver
PHISICAL SPECIFICATIONS
  • Overall dimensions: (hxlxd) 1292x350x450 mm
  • Weight approx .: 80 kg

Información para Pedidos

50-C10D02
AUTOMAX SMART line, Automatic control console, for connection to two testing frames. PC not included. 230 V, 50-60 Hz, 1 ph

50-C10D04
AUTOMAX SMART line, Automatic control console. PC not included. 110 V, 60 Hz, 1 ph

Información Adicional

Standards
The following standards refer to the execution of the testing procedures (eg load rate, load application, accuracy, etc.) as the mechanical and physical requirements.
  • EN 12390-3 
    Compressive strength of test specimens
  • EN 12390-4 
    Specification for compression testing machine
  • EN 12390-5 
    Flexural strength of test specimens
  • EN 12390-6 
    Tensile splitting strength of test specimens
  • EN 1338       
    Concrete paving blocks
  • EN 1339       
    Concrete paving flags
  • EN 1340       
    Concrete kerb units
  • EN 196-1     
    Determination of cement strength
  • EN 772-1     
    Determination of compressive strength of masonry units (blocks)
  • ASTM C39   
    Compressive strength of cylindrical concrete specimens
  • ASTM C78   
    Flexural strength of concrete. Third point loading
  • ASTM C293 
    Flexural strength of concrete. Center point loading
  • ASTM C496 
    Splitting tensile test of cylindrical concrete specimens
  • AASHTO T22
    Compressive strength of cylindrical concrete specimens
 

Actualización

Third frame facility
50-C10D / 3F

Upgrading the Automax System for a third frame connection and control. Frame selection via display / PC

Serial printer for Automax testers

50-Q60 / PR

Upgrade of a PILOT or AUTOMAX system to incorporate a serial graphic printer in the front panel, allowing results (including a load/time plot) to be printed at the end of test

Documentos